Linux und Intel 82599ES 10-Gigabit-SFI / SFP + -Verbindung sind immer inaktiv

Ich habe HP ProLiant DL360 GEN 9, wenn der Server startet, habe ich einen Link auf Intel 82599ES.
Nach dem Start von linux (Slackware 14.2 Kernel 4.4.19) ist die Verbindung nicht verfügbar (etwas wie spf-Leistung ist ausgefallen?).
Wie kann ich es reparieren?

# lspci | grep Network 04:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01) 04:00.1 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)  # ethtool eth0 Settings for eth0: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: Unknown! Duplex: Unknown! (255) Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: umbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: no  # ethtool -i eth0 driver: ixgbe version: 4.2.1-k firmware-version: 0x80000887 expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: no  # lsmod |grep -E 'ixgbe|mdio|igb|ioat|dca' ixgbe 221749 0 vxlan 34494 1 ixgbe ptp 12164 2 tg3,ixgbe mdio 3973 1 ixgbe ioatdma 33129 0 dca 6585 2 ixgbe,ioatdma hwmon 4199 4 tg3,ixgbe,coretemp,acpi_power_meter  # ethtool -m eth0 Identifier : 0x03 (SFP) Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID) Connector : 0x07 (LC) Transceiver codes : 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Transceiver type : 10G Ethernet: 10G Base-SR Encoding : 0x06 (64B/66B) BR, Nominal : 10300MBd Rate identifier : 0x00 (unspecified) Length (SMF,km) : 0km Length (SMF) : 0m Length (50um) : 80m Length (62.5um) : 30m Length (Copper) : 0m Length (OM3) : 300m Laser wavelength : 850nm Vendor name : FINISAR CORP. Vendor OUI : 00:90:65 Vendor PN : FTLX8571D3BCL-HP Vendor rev : A Option values : 0x00 0x1a Option : RX_LOS implemented Option : TX_FAULT implemented Option : TX_DISABLE implemented BR margin, max : 0% BR margin, min : 0% Vendor SN : MVA0TLN Date code : 16031211 Optical diagnostics support : Yes Laser bias current : 0.000 mA Laser output power : 0.0062 mW / -22.08 dBm Receiver signal average optical power : 0.0000 mW / -inf dBm Module temperature : 28.81 degrees C / 83.86 degrees F Module voltage : 3.3293 V Alarm/warning flags implemented : Yes Laser bias current high alarm : Off Laser bias current low alarm : On Laser bias current high warning : Off Laser bias current low warning : On Laser output power high alarm : Off Laser output power low alarm : On Laser output power high warning : Off Laser output power low warning : On Module temperature high alarm : Off Module temperature low alarm : Off Module temperature high warning : Off Module temperature low warning : Off Module voltage high alarm : Off Module voltage low alarm : Off Module voltage high warning : Off Module voltage low warning : Off Laser rx power high alarm : Off Laser rx power low alarm : On Laser rx power high warning : Off Laser rx power low warning : On Laser bias current high alarm threshold : 13.200 mA Laser bias current low alarm threshold : 4.000 mA Laser bias current high warning threshold : 12.600 mA Laser bias current low warning threshold : 5.000 mA Laser output power high alarm threshold : 1.0000 mW / 0.00 dBm Laser output power low alarm threshold : 0.2512 mW / -6.00 dBm Laser output power high warning threshold : 0.7943 mW / -1.00 dBm Laser output power low warning threshold : 0.3162 mW / -5.00 dBm Module temperature high alarm threshold : 78.00 degrees C / 172.40 degrees F Module temperature low alarm threshold : -13.00 degrees C / 8.60 degrees F Module temperature high warning threshold : 73.00 degrees C / 163.40 degrees F Module temperature low warning threshold : -8.00 degrees C / 17.60 degrees F Module voltage high alarm threshold : 3.7000 V Module voltage low alarm threshold : 2.9000 V Module voltage high warning threshold : 3.6000 V Module voltage low warning threshold : 3.0000 V Laser rx power high alarm threshold : 1.0000 mW / 0.00 dBm Laser rx power low alarm threshold : 0.0100 mW / -20.00 dBm Laser rx power high warning threshold : 0.7943 mW / -1.00 dBm Laser rx power low warning threshold : 0.0158 mW / -18.01 dBm